Differences

This shows you the differences between two versions of the page.

--- cobi.wms:keyence_settings [2025/12/15 11:11] – thuth
+++ cobi.wms:keyence_settings [2025/12/15 11:28] (current) – [KEYENCE BT-A700G – Scanner Parameters] thuth
@@ Line 1: / Line 1: @@
-===== KEYENCE BT-A700G – Scanner Parameters =====
+====== KEYENCE – Scanner Parameters ======
 ==== Purpose ====
-This guide describes the required scanner settings on the KEYENCE BT-A700G so that COBI.wms can correctly recognize and process barcodes (e.g., EAN/UPC, Code128, EAN128/GS1). Key points:
+This guide describes the required scanner settings on the KEYENCE BT-A700G so that COBI.wms can correctly recognize and process barcodes (e.g., EAN/UPC, Code128, EAN128/GS1). \\
+Key points:
   * Enable AIM ID Prefix (reliable barcode type identification)
@@ Line 12: / Line 13: @@
 ==== Step-by-step instructions ====
-=== 1) Open Android Settings (Fig. 1) ===
+==== 1) Open Android Settings ====
   - Open the app overview (home screen / list of all apps).
@@ Line 19: / Line 20: @@
 {{:cobi.wms:keyence1.png?400|}}
-=== 2) Open Scanner Settings (Fig. 2) ===
+==== 2) Open Scanner Settings ====
   - In Android Settings, select **Scanner** (scan parameters, code settings).
@@ Line 25: / Line 26: @@
 {{:cobi.wms:keyence2.png?400|}}
-=== 3) Open Data Formatting (Fig. 3) ===
+==== 3) Open Data Formatting ====
   - In the **Scanner** menu, scroll to the **Data** section.
@@ Line 32: / Line 33: @@
 {{:cobi.wms:keyence3.png?400|}}
-=== 4) Enable “AIM ID Prefix” (Fig. 4) ===
+==== 4) Enable “AIM ID Prefix” ====
   - Enable **AIM ID Prefix** (check the box).
@@ Line 41: / Line 42: @@
 The AIM ID adds an identifier to the scanned data so COBI.wms can reliably determine the **barcode type** (e.g., GS1/EAN128 vs. Code128). This is especially important for GS1 logic (AI structures).
-=== 5) Go back and open “Data Output” (Fig. 5) ===
+==== 5) Go back and open “Data Output” ====
   - Go **one step back** to the Scanner menu.
@@ Line 48: / Line 49: @@
 {{:cobi.wms:keyence5.png?400|}}
-=== 6) Set Transmission Type to “KeyEvent” (Fig. 6) ===
+==== 6) Set Transmission Type to “KeyEvent” ====
   - Under **Transmission type**, set the value to **KeyEvent**.
@@ Line 57: / Line 58: @@
 {{:cobi.wms:keyence6.png?400|}}
-=== 7) Enable Intent and configure Broadcast (Fig. 7) ===
+==== 7) Enable Intent and configure Broadcast ====
   - In **Data output**, tap **Intent**.
@@ Line 73: / Line 74: @@
 {{:cobi.wms:keyence7.png?400|}}
-=== 8) Set Intent extras: Code type / Raw data / Data (Fig. 8) ===
+==== 8) Set Intent extras: Code type / Raw data / Data ====
 Scroll further down in the Intent settings and set these values **manually**:
@@ Line 91: / Line 92: @@
   - Start scanning and validate the result.
-=== Troubleshooting / Support ===
+==== Troubleshooting / Support ====
 If issues persist:
@@ Line 102: / Line 103: @@
    * **screenshots** of the settings,
    * the **affected barcodes** (sample data)
-     to: **[support@cobisoft.de](mailto:support@cobisoft.de)**.
+     to: [[support@cobisoft.de|support@cobisoft.de]].